Покрытия для нефтегаза: клапаны, плунжеры, насосные штанги и трубопроводы

Покрытия для нефтегаза: клапаны, плунжеры, насосные штанги и трубопроводы

Oil and gas equipment fails in three ways that a coating can change: sand and proppant erosion, corrosive media attacking the surface, and metal-to-metal contact wearing a sealing face out of tolerance. The coating has to be chosen against the specific combination, because a layer that handles abrasion well can be the wrong choice in a sour, high-temperature well.

Component by component

ComponentFailure modeRecommended coating
Gate and ball valve seats, gates, ballsErosion from sand, galling, loss of shut-offHVOF WC-Co or WC-CoCr, 0.20-0.40 mm, ground and lapped
Plungers and liners (reciprocating pumps)Abrasive wear, corrosion pits, packing wearCr2O3 ceramic or WC-Co, 0.15-0.35 mm, polished
Sucker rods and couplingsRod-tubing wear, corrosion fatigueWC-Co or Ni-based alloy, 0.10-0.25 mm
Drill stabilisers, tool jointsSevere abrasion, impactWC-CoCr HVOF or PTA cladding for heavy duty
Flow lines, chokes, elbowsSand erosion at direction changesWC-Co internal coating, 0.10-0.30 mm
Structural steel under insulation (CUI)Trapped moisture, chloride, temperature cyclingThermal spray aluminium (TSA), sealed

Choose by medium, not by habit

The same valve can need two different coatings depending on what flows through it:

  • Sand or proppant laden: tungsten carbide, and the harder the better. Erosion resistance scales with hardness and density, which is why HVOF rather than plasma is used on sealing faces.
  • CO2 and chlorides with modest solids: WC-CoCr, where the chromium-bearing binder resists chloride attack better than plain cobalt.
  • Hot, oxidising, low-solids: Cr3C2-NiCr holds up where WC-Co starts to oxidise.
  • Chemical injection and acid service: chromium oxide or a sealed ceramic, chosen for chemical inertness rather than hardness.

Sour service: what a coating cannot do

In H2S-containing service, material selection is governed by ISO 15156 / NACE MR0175, and that qualification belongs to the base material and its heat treatment. A coating does not convert an unqualified steel into a qualified one, and it should never be presented as a way around the standard. What a coating can do in sour service is protect a qualified substrate from erosion and from mechanical damage during handling - that is a different and legitimate benefit.

Sealing faces: finish is the specification

On a valve seat, hardness alone does not restore shut-off. The coated face is ground and lapped flat, with the flatness and roughness specified for the seal class. We measure and record those numbers, because a seat that is hard but not flat leaks at pressure test and the whole reconditioning job has to be repeated.

Pipeline and flow line internals

Erosion in a flow line concentrates at bends, reducers and downstream of chokes, where particles hit the wall at an angle. Coating the internal surface of those sections - and the first straight length after them - removes the wear point without changing the line layout. Spools are coated individually so each can be blasted, sprayed and inspected before refit.

What we need to quote

Component drawing, base material and its NACE/ISO status, the medium (solids content, H2S/CO2, chlorides), temperature and pressure class, and the acceptance criteria for the sealing surface. For pipeline work, a spool list with diameters, lengths and bend radii is enough to quote.

Thickness against pressure class and clearance

A coating changes the geometry of the part it protects, and in oilfield equipment the clearances are already tight. A valve gate coated to 0.3 mm per side closes against a seat whose dimension was set for bare metal, so the coating thickness is planned with the assembly, not chosen from a catalogue. Where the clearance cannot absorb the layer, the mating part is machined to suit or the coating is applied only to the wear face.

Pressure class matters in a different way: the coating must not become a leak path. That is why sealing surfaces are coated, ground and lapped as a pair, and pressure-tested after reconditioning rather than assumed good because the hardness passed.

Refurbishment cycle

Valves, plungers and rods are consumables in abrasive service, and the practical question is the refurbishment interval. A coated part can be stripped and re-coated when the layer wears through, provided the base metal is still sound - typically two or three cycles before the substrate falls below minimum section. Planning that cycle is what turns coating from a repair into a maintenance strategy: the operator knows how many overhauls a body will take before it must be replaced.

Inspection and traceability

Oilfield customers usually want the record as much as the part: base material and its NACE status, coating material certificate, thickness and hardness readings, seal-face flatness, and the pressure test result. We supply that pack with each batch, which is also what makes a repeat order straightforward - the same parameters reproduce the same result.

Frequently asked questions

Can a coating make a valve suitable for sour service?

No. Sour service qualification under ISO 15156 / NACE MR0175 applies to the base material and its heat treatment. A coating can protect a qualified component from erosion and mechanical damage, but it does not upgrade the material's qualification.

Which coating is best for sand erosion in a choke or valve?

HVOF tungsten carbide - WC-Co for maximum abrasion resistance, or WC-CoCr where chlorides are also present. Density and hardness both matter, which is why the HVOF process rather than plasma is used on sealing and flow-control surfaces.

How is a coated valve seat finished?

Ground and lapped flat after spraying, to the flatness and roughness required for the seal class. Hardness without flatness does not restore shut-off, so the finishing step is part of the coating job.

Do you coat sucker rods and drill tools?

Yes - carbide or Ni-based layers on sucker rods for rod-tubing wear, and WC-CoCr or PTA cladding on stabilisers and tool joints where impact is also present.

Related Coating Services

Сверхзвуковое дуговое оборудование SX-1080 — графитовые изделия с медно-алюминиевым композитным покрытием, нанесённым методом напыления
Graphite boat—sprayed with zirconia (yttrium)

Сверхзвуковое дуговое оборудование SX-1080 — графитовые изделия с медно-алюминиевым композитным покрытием, нанесённым методом напыления

Сверхзвуковое дуговое напыление медно-алюминиевых композиционных покрытий на графитовые изделия с использованием оборудования SX-1080, что повышает теплопроводность и стойкость к окислению высокотемпературных графитовых приспособлений.

Подробнее →
Графитовая лодочная посуда с покрытием из циркония — линия производства плазменного напыления
Graphite boat—sprayed with zirconia (yttrium)

Графитовая лодочная посуда с покрытием из циркония — линия производства плазменного напыления

Готовая производственная линия плазменного напыления для нанесения циркониевых покрытий на графитовые лодочки с W-образным желобком, используемые в спекании электронной керамики, включая подготовку поверхности, процесс напыления и вспомогательное оборудование.

Подробнее →
Графитовое лодочное блюдо, покрытое цирконием
Graphite boat—sprayed with zirconia (yttrium)

Графитовое лодочное блюдо, покрытое цирконием

Покрытие из цирконии, обработанное на поверхностях графитовой лодочки с использованием оборудования для плазменного напыления, улучшает шероховатость поверхности и обеспечивает термостойкость для оснастки спекания.

Подробнее →