Порошок цирконии (YSZ / стабилизированный кальцием)

Порошок цирконии (YSZ / стабилизированный кальцием)

The phase problem that defines the material

Pure zirconia cannot be used as a coating. It exists in three crystal structures - monoclinic at room temperature, tetragonal above roughly 1170 C, cubic above roughly 2370 C - and on cooling the tetragonal-to-monoclinic transformation comes with a 3-5 percent volume expansion. A sprayed pure zirconia coating therefore cracks itself apart on the first cool-down.

The fix is stabilisation. Adding yttria, calcia, magnesia or ceria holds the tetragonal phase metastable at room temperature, so the coating stays intact. That is why every zirconia spray powder you will be quoted is a stabilised grade, and why the stabiliser content is the single most important line on the datasheet.

Grades and what they are for

GradeStabiliserPrimary use
7-8 % YSZYttria 7-8 wt %Thermal barrier coatings on turbine and engine parts - the standard aerospace and power generation grade
YSZ (20-25 % Y2O3)High yttriaWear and corrosion resistance, where thermal insulation is not the point
Calcia stabilised (CaO)Calcia ~5 %General purpose TBC and wear coatings; cheaper, slightly less phase-stable at high temperature
Magnesia stabilised (MgO)Magnesia ~24 %Heavy-duty wear and erosion coatings, hot corrosion environments
Ceria stabilisedCeriaHot corrosion resistance where yttria-stabilised material is attacked by sulphur and vanadium

Porosity is a design parameter, not a defect

A fully dense zirconia coating fails quickly. The ceramic and the metal expand at different rates, and every thermal cycle adds strain that a dense layer cannot absorb. Sprayed TBCs are therefore deliberately kept at 8-15 percent porosity, which is what lets the coating survive hundreds of cycles instead of five.

This is why "denser is better" is the wrong instinct for a thermal barrier, and why a supplier quoting near-zero porosity for a TBC has misunderstood the application. For wear-resistant zirconia the logic reverses: there you want the density, and you accept that it will not tolerate thermal cycling.

Thickness limits

TBCs run 0.25-0.40 mm of ceramic over a 0.10-0.15 mm MCrAlY bond coat. Above about 0.4 mm the insulation gain flattens out while the stored strain energy keeps climbing, and spallation at edges and corners becomes the failure mode. If a design calls for 1 mm of ceramic, the design is wrong - not the coating.

For wear applications zirconia is usually applied at 0.15-0.35 mm and can be thicker, but it is a different grade and a different conversation.

Spraying notes

Air plasma is the standard process for TBCs; vacuum plasma gives a denser, more oxidation-resistant bond coat and is used where the specification demands it. Powder cuts are typically -45/+11 um or -45/+22 um depending on gun and feed system. Spheroidised, agglomerated powder flows better and gives more consistent porosity than crushed material - on a production cell that consistency is worth the price difference.

A TBC without a proper bond coat is not a TBC. The bond layer provides oxidation resistance and the mechanical key the ceramic needs; skipping it to save cost is the most common reason a cheap TBC fails early.

What we need to quote

Service temperature and cycle count, substrate and bond coat specification, required thickness, whether the requirement is insulation or wear, and the acceptance standard. If you are working to an aerospace or power generation specification, tell us which one - the stabiliser content and porosity limits are set by that document, not by preference.

The bond coat is not optional

An MCrAlY bond layer does two jobs that the ceramic cannot do for itself. It provides oxidation resistance, because the ceramic is transparent to oxygen at temperature and the bond coat is what actually grows the protective alumina scale. And it provides the mechanical key - the roughness and the intermediate expansion coefficient that let a 0.3 mm ceramic layer stay attached through hundreds of cycles.

Typical bond coats are NiCrAlY or NiCoCrAlY at 0.10-0.15 mm, applied by HVOF or vacuum plasma. Skipping the bond coat to save cost is the most common reason a low-priced TBC fails in the first few months, and it is not something a thicker ceramic layer can compensate for.

Frequently asked questions

Why does a zirconia coating need a stabiliser?

Because pure zirconia transforms from tetragonal to monoclinic on cooling, with a 3-5 percent volume expansion that cracks the coating. Yttria, calcia, magnesia or ceria hold the tetragonal phase metastable at room temperature so the coating stays intact.

Why is porosity allowed in a thermal barrier coating?

To absorb the strain from thermal expansion mismatch between ceramic and metal. A dense ceramic spalls within a few cycles; 8-15 percent porosity lets it survive hundreds. Porosity is specified and measured, not a manufacturing defect.

What is the maximum TBC thickness?

About 0.40 mm of ceramic over a 0.10-0.15 mm bond coat. Beyond that the insulation benefit flattens while stored strain energy keeps rising, and edge spallation becomes the failure mode.

Can I use zirconia for wear resistance instead of a thermal barrier?

Yes, but with a different grade and a different expectation. High-yttria or magnesia-stabilised zirconia is used for wear and erosion, applied denser than a TBC. It will not tolerate the thermal cycling a TBC is designed for, so the two applications should not be confused.