Наземная рельсовая система с седьмой осью для распылительных роботов

Наземная рельсовая система с седьмой осью для распылительных роботов

What a seventh axis actually adds

A six-axis robot has a fixed working envelope, and anything outside it has to be brought into the envelope by a positioner. That works for parts that rotate. It does not work for a part that is simply long: a 6 m shaft, a long hydraulic cylinder, a row of identical brackets on a frame. Mounting such a part on a turntable gives you a very large swing and a very small useful spray zone.

A ground rail solves it the other way round. The part stays still and the robot travels along it, so the cell becomes a line rather than a circle. The arm keeps working near its base, which is where it is stiffest and most accurate, and the rail provides the long travel at a fraction of the cost of a robot with equivalent reach.

Mechanics

The track base is welded from high-strength structural steel with premium plate, which gives the mass and stiffness needed to keep the rail straight under a moving, accelerating robot. A rail that deflects shows up in the coating as a thickness wave with the same period as the rail's natural frequency, so stiffness is a coating-quality parameter and not just a structural one.

  • Drive. Rack and pinion for long travels and high thrust; the pinion is preloaded against the rack to remove backlash.
  • Guidance. Linear guide rails with recirculating carriages, protected by stainless steel cover plates fixed to the steel frame with screws.
  • Cover plates in sections. Each section opens for maintenance, so the rack and guides can be cleaned without dismantling the axis.
  • Scale rulers on both sides of the direction of travel, so the current position of the robot can be read from either side of the cell.

Single controller, single program

The rail uses an external-axis motor from the same brand as the robot arm, which means the robot controller drives both. The practical consequences are worth listing because they are the reason to insist on a matched motor rather than a third-party drive:

  • The rail can be jogged manually from the teach pendant, and programmed in the same program as the arm.
  • Motion is coordinated: the arm can spray while the rail is still moving, so there is no stop-start stripe at each rail position.
  • One safety system, one set of limits, one backup. A separate rail drive means two controllers that have to be interlocked and two programs that have to be kept in step.

Safety at the ends

Safety devices are fitted at both ends of travel and detect when the robot is about to exceed its stroke, stopping the axis before the mechanical buffer is reached. Because the rail is long, the ends are also where people walk, so the end stops are usually combined with a physical guard and a scanner zone that slows the axis when someone enters.

Sizing the rail

Three numbers decide the specification: the length of the spray zone, the acceleration the process allows, and the mass being moved. Acceleration matters because a fast traverse between parts is wasted if the rail rings afterwards - the arm needs a moment to settle before the gun fires, and that settling time is part of the cycle. Where the cycle is tight we specify a heavier rail rather than a faster one.

Installation

The rail is set on a levelled foundation or on a machined steel plinth, shimmed and grouted, then the robot is mounted on the carriage and the whole axis is referenced. Alignment is checked over the full travel, not at the two ends only, because a rail that is straight at both ends and bowed in the middle will spray a bowed part correctly and a straight part badly. Cable chain, gun services and dust extraction connections are routed along the rail with the same allowance for flex as the arm dress pack.

What we need to quote

Part length and the length of the actual spray zone, part mass and how it is supported, the process and required traverse speed, the available floor length, and whether the cell will be relocated later. A rail designed for a fixed installation and one designed to be moved are different structures.

Frequently asked questions

When is a rail cheaper than a bigger robot?

When the part is long and the coating zone moves. A rail costs less than a robot with twice the reach, and it keeps the arm working near its base where it is stiffest and most accurate. For parts longer than roughly 2.5 m the rail is usually the better answer; below that a longer arm is simpler to install and easier to relocate.

Does the rail need a second controller?

No. The rail uses an external-axis motor from the same brand as the robot, driven by the robot controller, so the rail and the arm are one kinematic system. That means one program, one teach pendant and coordinated motion - the arm can spray while the rail is still moving.

What maintenance does the rail need?

Rack and pinion lubrication, cover plate inspection, and a check of the end-of-travel switches at each service interval. The stainless cover plates are in sections and each section opens, so the rack, the linear guides and the cable chain can be inspected without removing the robot.

Related Spray Equipment

Суперзвуковая система распыления воздух-топливо SX-HVAF8000
Сверхзвуковое напыление

Суперзвуковая система распыления воздух-топливо SX-HVAF8000

Воздушно-топливная система HVAF для карбидных покрытий: более низкая температура пламени, чем у HVOF, более высокая скорость частиц, возможность ультрамелкого WC, HMI Siemens и независимые газовые контуры.

Подробнее →
Пескоструйная машина коробочного типа SX-900F
Auxiliary Equipment & Automation

Пескоструйная машина коробочного типа SX-900F

Пневмопульсовая камера для подготовки поверхности перед покрытием: регулируемый циклонный сепаратор, фильтр-циклон с вибрационной очисткой, отделка Sa 2.5-3 на литых деталях, сварных конструкциях и формах.

Подробнее →
Винтовой воздушный компрессор для термораппинга
Auxiliary Equipment & Automation

Винтовой воздушный компрессор для термораппинга

Подача сжатого воздуха для плазменных, дуговых и HVAF ячеек: регулировка объема подачи от 0 до 100%, выбор осушителя и фильтрации, а также показатели расхода, необходимые каждому процессу.

Подробнее →